Q Logic Network Card QLE8042 User Guide

[ Quick Start Guide ]  
CONVERGED NETWORK ADAPTER INSTALLATION  
z
 
Quick Start Guide  
Installation Instructions  
This Quick Start Guide describes how to install and configure your new QLogic Converged Network Adapter (CNA) in  
four simple steps:  
Step 1. Verify the package contents.  
Step 2. Install the CNA hardware.  
Step 3. Install the CNA drivers.  
Step 4. Install the SANsurfer FC HBA Manager (FCoE support included).  
Keep the CNA in the antistatic bag until installation. The CNA contains parts that can be damaged by  
electrostatic discharge (ESD). Before handling the CNA, use standard methods to discharge static  
electricity. Place the CNA on the bag when examining it. Retain the bag for future use.  
CAUTION!  
Step 1. Verify the Package Contents:  
The QLogic CNA is shipped with the following items  
QLogic CNA  
Quick Start Guide (this document)  
SANsurfer CD  
Step 2. Install the CNA Hardware  
To install the CNA hardware, you need to open the computer and locate the appropriate bus slot. If necessary, consult  
your computer system manual for instructions to remove the computer cover.  
Follow these steps to install the CNA hardware:  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
Power off the computer, then disconnect the power cable.  
Remove the computer cover and find an empty PCIe x8 bus slot.  
Pull out the slot cover (if any) by removing the screw or releasing the lever.  
Grasp the CNA by the top edge and seat it firmly into the appropriate slot.  
Refasten the CNA’s retaining bracket using the existing screw or lever.  
Close the computer cover.  
Plug the appropriate Ethernet cable (either copper or optical) into the CNA.  
Plug in the power cable and turn on the computer.  
3
 
CNA  
LEVER  
SCREW  
PCI EXPRESS x8 SLOT RE-  
QUIRED FOR QLOGIC CNAs  
CNA RETAINING  
BRACKET  
SLOT COVERS  
SYSTEM  
CHASSIS  
Sample Motherboard and Slots  
Step 3. Install the CNA Drivers  
To install the FCoE drivers:  
1.  
2.  
3.  
4.  
From the driver list at the bottom of the page, select FCoE CNAs and QLE8042.  
Select the appropriate driver for your operating system.  
Follow the included instructions for installing the downloaded driver.  
To install the Ethernet drivers:  
1.  
2.  
Go to http://support.intel.com and search for 82598 10 Gigabit Ethernet Controller in the Download  
Center section.  
Follow the instructions provided on the Intel website to install the drivers.  
4
 
Step 4. Install the SANsurfer FC HBA Manager (FCoE Support Included)  
To install the SANsurfer FC HBA Manager from the CD:  
1.  
2.  
3.  
4.  
5.  
Select your applicable operating system.  
Click I Accept on the License Agreement.  
Select your specific operating system.  
Select the SANsurfer FC HBA Manager install file.  
Follow the on-screen directions to complete the installation.  
Congratulations! You have successfully installed your QLogic CNA!  
To obtain the most current drivers, management tools, user instructions, and documentation, please visit the  
QLogic website at http://driverdownloads.qlogic.com and download the latest versions.  
The following section contains additional information about the QLogic CNA, including the LED scheme,  
warranty, and laser safety information.  
CNA LEDs  
QLE8042 CNA LED Scheme  
Green LED  
(Activity, TX/RX)  
Green LED (Link)  
Activity  
Off  
On  
On  
Off  
Off  
Power on (no link)  
Link established, no activity  
Flashing  
Link established, TX/RX activity  
Warranty  
Please check the QLogic Web site at http://www.qlogic.com/Support/warranty.aspx for warranty details.  
Laser Safety  
FDA Notice  
This product complies with DHHS Rules 21CFR Chapter I,Subchapter J. This product has been designed and manufactured according to  
IEC60825-1 on the safety label of laser product.  
Class 1 Laser Product  
Appareil laser de classe 1  
Produkt der Laser Klasse 1  
Luokan 1 Laserlaite  
Caution—Class 1 laser radiation when open  
Do not view directly with optical instruments  
CLASS I LASER  
Attention—Radiation laser de classe 1  
Ne pas regarder directement avec des instruments optiques  
Vorsicht—Laserstrahlung der Klasse 1 bei geöffneter Abdeckung  
Direktes Ansehen mit optischen Instrumenten vermeiden  
Varoitus—Luokan 1 lasersäteilyä, kun laite on auki  
Älä katso suoraan laitteeseen käyttämällä optisia instrumenttej  
5
 
Agency Certification  
QLogic CNAs  
The following sections contain a summary of EMC/EMI test specifications performed on the QLogic CNAs to comply with radiated emission,  
radiated immunity, and product safety standards.  
EMI and EMC Requirements  
FCC Part 15 compliance: Class A (QLE8042)  
FCC compliance information statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including  
interference that may cause undesired operation.  
ICES-003 compliance: Class A (QLE8042)  
For QLE8042 CNAs: This Class A digital apparatus complies with Canadian ICES-003.Cet appareil numériqué de la classe A est  
conformé à la norme NMB-003 du Canada.  
CE Mark 2004/108/EC EMC Directive compliance:  
EN55022:2006/CISPR22:2006 - Class A (QLE8042)  
EN55024:1998  
Immunity Standards  
EN61000-4-2  
EN61000-4-3  
EN61000-4-4  
EN61000-4-5  
EN61000-4-6  
EN61000-4-8  
:
:
:
:
:
:
ESD  
RF Electro Magnetic Field  
Fast Transient/Burst  
Fast Surge Common/ Differential  
RF Conducted Susceptibility  
Power Frequency Magnetic Filed  
EN61000-4-11: Voltage Dips and Interrupt  
EN61000-3-2  
EN61000-3-3  
:
:
Harmonic Current Emission  
Voltage Fluctuation and Flicker  
VCCI: Class A (QLE8042)  
AS/NZS CISPR22: Class A (QLE8042)  
CNS 13438: Class A (QLE8042)  
For QLE8042 CNAs  
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case, the user may  
be required to take adequate measures.  
MIC: Class A (QLE8042)  
For QLE8042 CNAs: Korea MIC Class A Certified  
Product Name/Model  
Certification holder  
Fibre Channel CNA  
QLogic Corporation  
Manufactured date  
Refer to date code listed on product  
QLogic Corporation/USA  
Manufacturer/Country of origin  
A class equipment  
(Business purpose info/telecommunications  
equipment)  
As this equipment has undergone EMC registration for business  
purpose, the seller and/or the buyer is asked to beware of this point  
and in case a wrongful sale or purchase has been made, it is asked  
that a change to household use be made.  
6
 
Korean Language Format— Class A  
Product Safety Compliance  
UL, cUL product safety: QLE8042  
UL60950  
CSA C22.2 No.60950  
Class 1 Laser Product per DHHS 21CFR (J)  
2006/95/EC low voltage directive: QLE8042  
TUV:  
-EN60950-1:2001+A11  
-EN60825-1:1994+A1+A2  
-EN60825-2:2004  
7
 
8
 
9
 
10  
 
© 2008 QLogic Corporation. QLogic, the QLogic logo, and SANsurfer are registered trademarks or trademarks of QLogic  
Corporation. All other brands and product names are trademarks or registered trademarks of their respective owners.  
Information supplied by QLogic is believed to be accurate and reliable. QLogic Corporation assumes no responsibility  
for any errors in this brochure. QLogic Corporation reserves the right, without notice, to makes changes in product  
design or specifications.  
 
FE0154501-00  B  
QLogic Corporation  
949.389.6000  
26650 Aliso Viejo Parkway  
Aliso Viejo, CA 92656  
FE0154501-00 B  
J
 

Q Logic Switch FIRMWARE VERSION 74 User Guide
RCA DVD Player RTD315W User Guide
RCA Garage Door Opener RCRN08GR User Guide
RCA Speaker RP 9990 User Guide
Roberts Radio Microcassette Recorder RC9907 User Guide
Salton Juicer JM1 User Guide
Samsung Blood Pressure Monitor BF 180M User Guide
Samsung Speaker System HW E350 User Guide
Sanyo Car Satellite TV System HT27547 User Guide
Senco Nail Gun GT90CH User Guide