Rangemaster Ventilation Hood RMG2H60SS User Guide

RMG2H60SS  
RMG2H90SS  
Instructions Manual  
 
RECOMMENDATIONS AND SUGGESTIONS  
The Instructions for Use apply to several versions of this appliance. Accord-  
ingly, you may find descriptions of individual features that do not apply to  
your specific appliance.  
INSTALLATION  
The manufacturer will not be held liable for any damages resulting from in-  
correct or improper installation.  
The minimum safety distance between the cooker top and the extractor  
hood is 450 mm.  
Check that the mains voltage corresponds to that indicated on the rating  
plate fixed to the inside of the hood.  
For Class I appliances, check that the domestic power supply guarantees  
adequate earthing.  
Connect the extractor to the exhaust flue through a pipe of minimum diame-  
ter 120 mm. The route of the flue must be as short as possible.  
Do not connect the extractor hood to exhaust ducts carrying combustion  
fumes (boilers, fireplaces, etc.).  
• If the extractor is used in conjunction with non-electrical appliances (e.g. gas  
burning appliances), a sufficient degree of aeration must be guaranteed in  
the room in order to prevent the backflow of exhaust gas. The kitchen must  
have an opening communicating directly with the open air in order to  
guarantee the entry of clean air.  
450 mm min.  
USE  
The extractor hood has been designed exclusively for domestic use to elimi-  
nate kitchen smells.  
Never use the hood for purposes other than for which it has ben designed.  
Never leave high naked flames under the hood when it is in operation.  
Adjust the flame intensity to direct it onto the bottom of the pan only, making  
sure that it does not engulf the sides.  
Deep fat fryers must be continuously monitored during use: overheated oil  
can burst into flames.  
Do not flambè under the range hood; risk of fire  
This appliance is not intended for use by persons (including children) with  
reduced physical, sensory or mental capabilities, or lack of experience and  
knowledge, unless they have been given supervision or instruction concern-  
ing use of the appliance by a person responsible for their safety.  
Children should be supervised to ensure that they do not play with the appli-  
ance.  
MAINTENANCE  
Switch off or unplug the appliance from the mains supply before carrying out  
any maintenance work.  
Clean and/or replace the Filters after the specified time period.  
Clean the hood using a damp cloth and a neutral liquid detergent.  
The symbol  
on the product or on its packaging indicates that this product may not be treated  
as household waste. Instead it shall be handed over to the applicable collection point for the  
recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly,  
you will help prevent potential negative consequences for the environment and human health,  
which could otherwise be caused by inappropriate waste handling of this product. For more  
detailed information about recycling of this product, please contact your local city office, your  
household waste disposal service or the shop where you purchased the product.  
EN  
3
 
CHARACTERISTICS  
Dimensions  
EN  
4
 
Components  
Ref. Q.ty Product Components  
15  
1
1
Hood Body, complete with: Controls, Light,  
Blower, Filters  
14.1  
2
1
1
1
1
1
2
1
Telescopic Chimney comprising:  
Upper Section  
Lower Section  
Reducer Flange ø 150-120 mm  
Adapting ring ø 120-125 mm  
Air Outlet Connection Extension  
Air Outlet Connection  
7.3  
2.1  
2.2  
9
10  
14.1  
15  
12a 7.2.1  
11  
10  
9
Ref. Q.ty Installation Components  
7.2.1  
7.3  
11  
12a  
12c  
2
1
6
6
6
Upper Chimney Section Fixing Brackets  
Air Outlet Connection Support  
Wall Plugs  
Screws 4,2 x 44,4  
Screws 2,9 x 9,5  
2.1  
2.2  
12c  
2
Q.ty Documentation  
Instruction Manual  
1
11  
12a  
1
EN  
5
 
INSTALLATION  
Wall drilling and bracket fixing  
7.2.1  
11  
116 116  
12a  
Wall marking:  
• Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the  
centre of the area in which the hood will be installed.  
• Draw a horizontal line at 1040 mm above the hob.  
• Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit align-  
ing the centre (notch) with the vertical reference line.  
• Mark the wall at the centres of the holes in the bracket.  
• Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the  
upper chimney section supplied), aligning the centre (notch) with the vertical line.  
• Mark the wall at the centres of the holes in the bracket.  
• Mark a reference point as indicated at 116 mm from the vertical reference.  
• Repeat this operation on the other side.  
• Drill ø 8 mm holes at all the centre points marked.  
• Insert the wall plugs 11 in the holes.  
• Fix the lower bracket 7.2.1 using the 12a screws (4,2 x 44,4) supplied.  
• Fix the upper bracket 7.2.1 and the air outlet connection support 7.3 together using the 2  
screws 12a (4,2 x 44,4) supplied.  
• Insert the two screws 12a (4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap  
of 5-6 mm between the wall and the head of the screw.  
EN  
6
 
Mounting the hood body  
• Before attaching the hood body, tighten the two screws Vr lo-  
cated on the hood body mounting points.  
Vr  
• Hook the hood body onto the screws 12a.  
• Fully tighten support screws 12a.  
• Adjust screws Vr to level the hood body.  
12a  
Connections  
DUCTED VERSION AIR EXHAUST SYSTEM  
ø 150  
ø 125  
When installing the ducted version, connect the hood to the  
chimney using either a flexible or rigid pipe ø 150 or 125 mm,  
the choice of which is left to the installer.  
10  
9
• To install a ø 125 mm air exhaust connection, insert the re-  
ducer flange 9 on the hood body air outlet and the adapting  
ring ø120-125 10 on the reducer flange.  
• Fix the pipe in position using sufficient pipe clamps (not sup-  
plied).  
• Remove any activated charcoal filters.  
14.1  
7.3  
15  
RECIRCULATION VERSION AIR OUTLET  
• Insert the connection extension pieces laterally 14.1 in connec-  
tion 15.  
• Insert the Connector 15 into the Support bracket 7.3 and fix it  
with a screw.  
• Make sure that the outlet of the extension pieces 14.1 is hori-  
zontally and vertically aligned with the chimney outlets.  
• Connect the air outlet connection 15 to the hood body outlet  
using either a flexible or rigid pipe ø 150 mm, the choice of  
which is left to the installer.  
ø 150  
• Ensure that the activated charcoal filters have been inserted.  
7
EN  
 
ELECTRICAL CONNECTION  
• Connect the hood to the mains through a two-pole switch hav-  
ing a contact gap of at least 3 mm.  
• Remove the grease filters (see paragraph Maintenance) being  
sure that the connector of the feeding cable is correctly inserted  
in the socket placed on the side of the fan.  
7.2.1  
Flue assembly  
12c  
12c  
Upper exhaust flue  
• Slightly widen the two sides of the upper flue and hook them  
behind the brackets 7.2.1, making sure that they are well  
seated.  
• Secure the sides to the brackets using the 4 screws 12c (2,9 x  
9,5) supplied.  
2.1  
2.2  
2
• Make sure that the outlet of the extensions pieces is aligned  
with the chimney outlets.  
12c  
Lower exhaust flue  
• Slightly widen the two sides of the flue and hook them be-  
tween the upper flue and the wall, making sure that they are  
well seated.  
• Fix the lower part laterally to the hood body using the 2 screws  
12c (2,9 x 9,5) supplied.  
EN  
8
 
USE  
S1  
L
T1  
T2  
T3  
T4  
Control Panel  
The hood can be switched on pushing directly onto the requested speed without firstly having  
to select 0/1 button.  
KEY  
L
LED  
FUNCTIONS  
0/1 Light  
Turns lighting on and off.  
T1 0/1 Motor on  
First speed.  
When pressed for about 1 seconds the motor is switched off.  
T2 Speed  
T3 Speed  
T4 Speed  
on  
Second speed.  
Third speed.  
Max. speed  
on  
Fixed  
Flashing  
Intensive speed.  
Suitable for the strongest cooking vapours and odours.  
The function becomes active when the button is pushed  
for about 2 seconds. After 10 minutes of functioning it  
turns off automatically. This function can be interrupted  
by means of pressing any of the buttons.  
S1 Led  
Fixed  
Indicates that the Metal grease filters saturation alarm has  
been triggered, and the filters need to be washed. The  
alarm is triggered after 100 working hours. (Reset; check  
the Maintenance-paragraph)  
Flashing  
indicates that the activated charcoal odour filter satura-  
tion alarm has been triggered, and the filter has to be re-  
placed; the metal grease filters must also be washed. The  
activated charcoal odour filter is triggered after 200  
working hours. (Activation and Reset; check the Mainte-  
nance-paragraph))  
9
EN  
 
MAINTENANCE  
REMOTE CONTROL (OPTIONAL)  
The appliance can be controlled using a remote control powered  
by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-  
AAA type.  
• Do not place the remote control near to heat sources.  
• Used batteries must be disposed of in the proper manner.  
Cleaning the Comfort Panels  
• Pull the Comfort Panel to open it.  
• Disconnect the panel from the hood canopy by sliding the fix-  
ing pin lever.  
• The comfort panel must never be washed in a dishwasher.  
• Clean the outside using a damp cloth and neutral liquid deter-  
gent.  
• Clean the inside as well using a damp cloth and neutral deter-  
gent; do not use wet cloths or sponges, or jets of water; do not  
use abrasive substances.  
• When the above operation has been completed, hook the panel  
back to the hood canopy and close it by turning the knob in the  
opposite direction.  
EN  
10  
 
Grease filters  
CLEANING METAL SELF- SUPPORTING GREASE FIL-  
TERS  
Alarm signal reset  
• Switch off the lights and extractor motor.  
• Press button T3 for at least 3 seconds, until the leds  
start to flash.  
Cleaning the filters  
• The filters are washable and must be cleaned at least  
every 2 months of operation, or more frequently for  
particularly heavy usage.  
• Pull the Comfort Panel to open it.  
• Remove the filters one at a time by pushing them to-  
wards the back of the group and pulling down at the  
same time.  
• Wash the filters, taking care not to bend them. Allow  
them to dry before refitting.  
• When refitting the filters, make sure that the handle  
is visible on the outside.  
ATTENTION: Remove the filters one by one pushing  
them towards the back side of the hood and simultane-  
ously pulling downwards and towards the centre of the  
hood (only in case of 60 cm hood version).  
EN  
11  
 
Activated charcoal filter (Recirculation version)  
The filter is not washable and cannot be regenerated. It must be replaced when led S1 flashes  
or at least every 4 months. The alarm signal will only light up when the extractor motor is swi-  
tched on.  
Alarm signal activation  
• In Recirculation version Hoods, the Filter saturation alarm can be enabled on installation or  
at a later date. Turn the Lights and the suction Motor off.  
• Disconnect the Hood using the Main switch or the double-pole switch on the mains power  
supply.  
• Restore the connection by pressing and holding T1.  
• Release the button. All five LEDs are turned on.  
Within 3 seconds press T1 until LEDs T1 and T4 flash in confirmation:  
-
-
LED flashes twice - Activated charcoal filter saturation alarm ENABLED.  
LED flashes once - Activated charcoal filter saturation alarm DISABLED.  
REPLACING THE ACTIVATED CHARCOAL FILTER  
Alarm signal reset  
• Switch off the lights and extractor motor.  
• Press button T3 for at least 3 seconds, until the leds start to  
flash.  
Replacing the Filter  
• Pull the Comfort Panel to open it.  
• Remove the metal grease filters  
• Remove the saturated activated carbon filter by releasing the  
fixing hooks  
• Fit the new filter by hooking it into its seating  
• Replace the metal grease filters.  
Lighting  
LIGHT REPLACEMENT  
20 W halogen light.  
• Remove the 2 screws fixing the Lighting support, and pull it  
out of from the Hood.  
• Extract the lamp from the Support.  
• Replace with another of the same type, making sure that the  
two pins are properly inserted in the lamp holder socket holes.  
• Replace the Support, fixing it in place with the two screws re-  
moved as above.  
EN  
12  
 
 
 
 
AGA RANGEMASTER LTD.  
436004188_ver1  
 

PYLE Audio Speaker PLBASS8 User Guide
Q See Dehumidifier QSWLOC User Guide
RCA Flat Panel Television BLC528 User Guide
Renesas Network Card HS1664ECH61H User Guide
Ricoh All in One Printer MP C3500 C4500 User Guide
Rotel CD Player RCD 02 User Guide
Samsung Flat Panel Television LA32R8 User Guide
Samsung Home Theater System AH68 01852B User Guide
Samsung Printer SRP 770II User Guide
Sanyo CRT Television AVM 2550S User Guide