RocketFish Computer Drive RF PHD25 User Guide

One connector is for data and bus power. The other connector is for additional  
power, if required. When you connect the USB 2.0 Y cable to the computer, use  
both A male-type connectors to make sure the enclosure has sufficient power.  
The operating system automatically detects and sets up the new drive.  
2 If the drive is not formatted, please take the steps below to format  
the drive.  
Package contents  
• RF-PHD25 enclosure  
• High-speed USB 2.0 Y-cable  
• CD that contains Roxio BackOnTrack  
backup software and User Guide  
Contenu du carton  
• Boîtier RF-PHD25  
• Câble en Y USB 2.0 à haut débit  
• CD avec l’application de sauvegarde Roxio Tournevis  
• Carrying case  
• Screws (4)  
• Screwdriver  
• Étui de transport  
• Vis (4)  
Quick Setup Guide  
BackOnTrack et le Guide de l’utilisateur  
• Guide d’installation rapide  
System requirements  
For Macintosh users:  
Configuration système requise  
One USB port  
1 Double-click on Macintosh HD.  
2 Click the Applications folder.  
3 Click the Utilities folder.  
4 Double-click Disk Utility.  
Un port USB  
Windows® 7, Windows Vista®, Windows® XP, or Mac OS 10.2.0 or higher.  
WindowsMD 7, Windows VistaMD, WindowsMD XP ou Mac OS 10.2.0 ou supérieur.  
PATA 2.5 Hard Drive Enclosure  
Boîtier pour disque dur  
Installing your hard drive in the enclosure  
1 Remove the two screws from the back panel, then pull the tray out from  
Installation du disque dur dans le boîtier  
1 Retirer les deux vis du panneau arrière, puis extraire le plateau du boîtier.  
PATA de 2,5 po (6,35 cm)  
Caja para disco duro PATA de 2.5"  
5 On the left side of the window, there are the drives connecting  
to the computer. Select the drive you want to format and then  
click the Erase tab.  
the enclosure.  
6 Verify Volume Format is set to MS-DOS file system, then click  
Erase.  
For Windows users:  
1 Right-click My Computer and select Manage.  
2 Click Disk Management on the left pane.  
2 Placer un disque dur formaté sur le plateau, connecter le connecteur de  
données au connecteur correspondant de la carte du boîtier, puis  
retourner le boîtier et fixer le disque dur à la plaque métallique à l’aide  
des deux vis (fournies).  
3 Right-click on the drive/device you want to format then select  
Format.  
2 Place a formatted hard drive into the tray, connect the data connector  
to the corresponding connector on the enclosure board, then turn the  
tray over and secure the drive to the metal plate with the two screws  
(provided).  
4 Occasionally, a warning may come out concerning active  
partition, click Yes.  
5 Click OK to format.  
Installing the backup software  
Notes:  
• The Roxio BackOnTrack software only runs on Windows Vista,  
Windows XP, or Windows 7. computers using USB.  
• Connect the hard drive enclosure to your computer before installing  
the software.  
3 Replacer le plateau assemblé dans le boîtier, puis le fixer avec les deux  
vis retirées précédemment.  
• Before installing the backup software, make sure that your Windows  
operating system has been updated to the latest service pack.  
1 Save all files and close all programs.  
3 Slide the assembled tray back into the enclosure, then secure it with  
the two screws you previously removed.  
2 Insert the included CD into the computer. The introductory screen  
appears automatically. If the screen does not appear, double-click  
the autorun.exe file on the CD.  
3 Click Install Roxio® BackOnTrack™ 3 LE. The Welcome screen opens.  
4 Click Next to begin the installation.  
5 Follow the instructions in the setup wizard, then click Next to  
continue.  
6 Click Finish to finalize installation.  
Connexion du boîtier à l’ordinateur  
Connecting the enclosure to a computer  
7 See the User Guide located on the CD for information on using the  
software.  
1 Brancher un câble USB 2.0 sur le boîtier, puis brancher le câble sur un  
port USB de l’ordinateur. Le système d’exploitation reconnaît  
automatiquement le nouveau disque.  
1 Plug a USB 2.0 cable into the enclosure, then plug the cable into a  
USB port on the computer. The operating system automatically  
recognizes the new drive.  
Disconnecting the enclosure from your computer  
For Windows users:  
Remarque : le boîtier est fourni avec un câble USB en Y, qui a deux connecteurs  
standard USB A de type mâle.  
Note: The enclosure comes with a USB 2.0 Y cable, which has two standard  
1 Right-click the Hotplug icon (located near the clock on the taskbar).  
2 Select the device you want to unplug, then click STOP.  
USB A male-type connectors.  
3 When Windows notifies you that it is safe to do so, unplug the  
enclosure from your computer.  
For Macintosh users:  
1 Drag the USB icon into the TRASH.  
2 Unplug the enclosure.  
One-year limited warranty  
© 2009 Best Buy Enterprise Services, Inc. Distributed by Best Buy Purchasing, LLC  
7601 Penn Avenue South, Richfield, MN USA 55423-3645  
QUICK SETUP GUIDE • GUIDE D’INSTALLATION RAPIDE •  
GUÍA DE INSTALACIÓN RÁPIDA  
RF-PHD25  
 

Q See DVR QR404 User Guide
Roberts Gorden Heat Pump EP 203 User Guide
Roberts Radio Cassette Player SRCD970 User Guide
Rosewill Network Card RC401 EX User Guide
Rotel CD Player RCC 945 User Guide
Salton Blender BL 1042 User Guide
Samson Stereo Amplifier BASS PRE AMP User Guide
Sanyo PDAs Smartphones POA PN01A User Guide
Schumacher Power Supply IP 125 User Guide
Sears Water Heater 15333262 User Guide