17. WARRANTY
Royal Sovereign International warrants the equipment sold is free from defects in
material and workmanship for a period of One (1) year for Parts and Labor from the date
of installation, excluding lamination rollers which are warranted for Six (6) months. This
warranty is extended only to the original purchaser. This warranty is the only warranty
made by Royal Sovereign International and cannot be modified or amended. Royal
Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy
under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such
defective part or product. These remedies are only available if Royal Sovereign’s
examination of the product discloses to Royal Sovereign’s satisfaction that such defects
actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized
alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.
OWNER'S MANUAL
RSC-1400C/1400H Laminators
The warranty made herein is in lieu of all other warranties, expressed or implied,
including any warranty or merchantability or fitness for a particular purpose. Royal
Sovereign will not be liable for personal damage or personal injury (unless primarily
caused by its negligence), loss of profit, or other incidental or consequential damages
arising out of the use or inability to use this equipment.
LIMITED WARRANTY
This warranty specifically does not cover damage to laminating rollers caused by knives,
razor blades, or any sharp objects or abrasives, or failure caused by adhesives, or
damage caused by lifting, tilting and/or any attempt to position the machine other than
rolling on the installed castors or feet on even surfaces, or improper use of the
machine. Warranty repair or replacement by Royal Sovereign or its authorized
Reseller(s) does not extend the warranty beyond the initial one year period from the
date of installation. Unauthorized customer alterations will void this warranty.
CORPORATE HEADQUARTERS
Royal Sovereign International Inc.
2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.
TEL : +1) 800-397-1025
FAX : +1) 201-750-1022
E-mail : [email protected]
RS Holland B.V.
Columbusstraat 25 - 3165 AC Rotterdam,
The Netherlands
E-mail : [email protected]
Royal Sovereign Inc. <Oversea Sales Office>
1001, World Meridian II, 426-5, Gasan-dong,
Geumcheon-gu, Seoul, 153-759, KOREA
TEL : +82)2-2025-8800 FAX : +82)2-2025-8830
E-mail : [email protected]
Read all instructions carefully before use.
For any Customer Support needs please choose the
RS International Australia PTY. LTD.
30 Prime Drive, Seven Hills, NSW 2147, Australia
TEL : +61) 2-9674-2127
RS Canada Inc.
164 Oakdale Road, Toronto, Ontario M3N 2S5
CANADA
Royal Sovereign International Inc.
FAX : +61) 2-9674-2027
TEL : +1
)
416-741-8400 FAX : +1 416-741-8185
)
E-mail : [email protected]
E-mail : [email protected]
19
RSC-1400C/H
4. INCLUDED WITH LAMINATOR
3. INSTALLATION
Thoroughly inspect the parts and the unit. It is imperative that any missing parts are
reported and a claim is filed with the reseller immediately upon receipt of shipment.
Note: The laminator should be installed by a trained service technician.
The laminator comes fully assembled, except for the feed table and paper guide to avoid
shipping damage. Upon arrival, thoroughly inspect the unit. It is imperative that any
shipping damage is reported and a claim is filed with the delivering carrier immediately
upon receipt.
Quantity
1
Picture
Part Name
Laminator
The laminator should be located in an area with adequate work space for feeding graphics
and lamination materials.
Owner's Manual
1
6/4
1
Avoid placing the laminator in a dusty area or near sources of extreme heat or cold.
3´´(76mm) / 2" (57mm) Auto Grip
Once the laminator is in place, lock the casters into position(“ON” position). Always unlock
the casters (“OFF” position) when moving to a different location.
Registration Card
L-wrench (2.5)
Dust Cover
1
ELECTRICAL REQUIREMENTS
Royal Sovereign recommends that a licensed electrician ensures proper power installation
to your laminator in accordance with electrical codes in your area.
1
1
1
Spare Motor Fuse - FUSE(50T)
(6.3A)
The laminator should have a dedicated power line.
MODEL
RSC-1400C
RSC-1400H
Spare Main Power Fuse - FUSE(65TS)
(5A)
220-240V
50/60HZ
120V
50/60HZ
220-240V
50/60HZ
120V
50/60HZ
Power Supply
8 - 1/4"Hexa head Bolt (M6 20mm)
8 - Spring Washer( 6.1)
single phase
10/10
12/12
(Included with option only)
12 - 3/16"screw (M5 10mm).
12 - Spring Washer( 5.1)
(Included with option only)
Front Feeder and Rear Rewinder Kit
(Included with option only)
2/2
4
120V UL
230V UL
240V UK
4 - 1/3"Hexa head Bolt (M8 70mm)
4 - Spring Washer( 8.5)
(Included with option only)
4 - 1/3"screw (M8 60mm).
4 - Spring Washer( 8.5)
(Included with option only)
4
4
220V EU
NUT M8)
220V AU
3
4
RSC -1400C/H
5. PRODUCT IDENTIFICATION
6. CONTROL PANEL
When the machine is initially turned on, the LED display window will show the speed and
temperature set at 1. (RSC-1400C and RSC-1400H).
12
11
2
1
3
4
10
9
5
6
8
13
7
RSC-1400H
RSC-1400C
Control Buttons
NO.
1
PART NAME
RSC-1400C
RSC-1400H
SAFETY COVER
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
1. TEMPERATURE DISPLAY: Display’s current temperature (RSC-1400C and RSC-1400H)
2
EMERGENCY SWITCH
FRAME-PAPER GUIDE
FEED TABLE
2. SPEED DISPLAY: Display’s current Speed.
3
3. TEMPERATURE BUTTON- (RSC-1400C and RSC-1400H): To change the temperature
4
(max. RSC-1400H: 122ºF, 50ºC ) of the upper roller, press up or down arrow button.
5
MAIN ROLLER
4. SPEED BUTTON: Adjusting the speed of the rollers. To change the speed of the rollers,
6
ASSEMBLY STAND
FOOT PEDAL
press the up or down arrow button.
7
8
TENSION CONTROL KNOBS
PRESSURE LEVER
CONTROL PANEL
UPPER IDLE BAR
5. RUN: To start the rollers.
9
6. STOP: To stop the rollers.
10
11
12
13
7. REV: To reverse the rollers, press and hold the REVERSE button.
RELEASE LINER TAKE UP
REMOTE CONTROL
5
6
RSC-1400C/H
7. SPEED AND TEMPERATURE SETTINGS
9. USING FOOT PEDAL AND REMOTE CONTROL
USING FOOT PEDAL
RSC-1400C/H
Speed(Ft/min,M/min)
4(1.2)
RSC-1400H
Temperature( F, C )
No Heating
No Heating
91(33)
Speed#
Temp.#
Place the foot pedal on the floor in front of the
machine. Once all correct settings are displayed, you
may use the foot pedal to operate the laminator for
“Hands Free Operation.” To activate the machine,
press the foot pedal once and then release. Repeat
to stop the rollers.
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
6(1.7)
7(2.2)
9(2.6)
97(36)
104(40)
10(3.1)
111(44)
12(3.6)
115(46)
14(4.2)
117(47)
15(4.5)
124(51)
16(5.0)
USING REMOTE CONTROL
1
2
3
8. ROLLER NIP SETTING
It is important to adjust the roller nip settings to the appropriate thickness of the board
being used. Use the guide below to adjust to the correct position.
Located on the rear left side of the laminator.
1. PRESS RUN – To activate the rollers.
2. PRESS STOP – To stop the rollers from turning.
3. PRESS REV – To reverse the rollers. Press and
hold the button (useful for jams or misted media).
Metric
NO.
Inches
(mm)
Lamination
1
1
2
3
4
5
Lamination
1/ 25"
3/16"~1/4"
3/ 8"~1/2"
3/5"
5-7
10-13
15
NOTE: If you don't want to
laminate,please place the
pressure lever to the "Open
position(NO.5)".
7
8
RSC-1400C/H
10. USING CROSS CUTTER
11. LOADING FILM
Royal Sovereign films are wound with the adhesive side facing the inside of the roll
The cross cutter is located on the rear exit table of the machine.
(adhesive in).
Loading films to upper and lower film shafts:
(See page 5 for assistance with parts identification.)
1. After lamination, move the cutter approximately to
the center of the completed application at the
desired point of detachment (Figure 1).
1. Adjust the auto grip to fit to the film and tighten the
auto grip screw (Figure 1).
Figure 1
Figure 2
Figure 3
Figure 1
2. Remove the upper and lower film shafts from the
machine and load the films (Center the upper and
lower films on the shaft). Note the direction of the
adhesives on the lower and upper films
(Figure 2).
2. Grasp film with one hand, press the cutter
downward into the application and slide it from
one end to the other. (Figure 2 & 3).
Figure 2
3. Load the upper and lower film shafts on the
machine (Figure 3).
Figure 3
9
10
RSC-1400C/H
9. Cut and separate the release liner and the film.
(Figure 3)
12. THREADING FILM
Figure 3
10. Thread the craft paper behind the Lower Idle Bar to
the top film that is resting on the main roller (do not
use the Lower Idle Bar for Mounting). (Figure 4)
12.1. Decaling
11. Reinstall the Feed Table and the Frame-Paper
Guide,and close the Safety Cover.
1. Turn the power switch on (“I” position). The Power
switch is located on the rear left side of the unit.
Figure 4
Figure 5
Figure 6
12. Adjust the nip setting to appropriate gap.
2. Complete the steps as in the “LOADING FILM”
section (see page 10).
13. Insert and push the leader board until they reach the
front nip point.
3. Set the top roller to the desired temperature (RSC-
1400C)
14. Push the Run button.
4. Take off the Frame-Paper Guide and the Feed Table.
15. Push the leader board into the rollers. (Figure 5)
5. Pull the top film down over the Safety Cover to the
bottom of the craft paper / Mounting film.
Figure 1
16. Adjust the top and bottom tension knob by rotating it
clockwise or counterclockwise. Turn it until the top
and bottom roll films have some resistance varies
(the tension depending on the film thickness; the
thicker the film the more tension is required).
(Figure 6)
6. Align and center the craft paper / Mounting film to the
top film and tighten the two lower core screws (Figure
1).
7. Thread the top film underneath the Upper Idle
Bar.(Figure 2)
8. Tape the top film on to the Release Liner Take-
Up.(Figure 2)
Figure 2
11
12
RSC-1400C/H
17. Press the Stop button when the leader board has completely exited from the rollers.
18. Use the Cross Cutter to cut the leader board from the web (see page 9).
4. Flip the image over the top roller and hold on to the
release liner (Figure 4).
19. Set the nip setting to the appropriate position for the Over-lamination / Decaling
application.
Figure 4
12.2. Mounting
1. Lay the decaled image face down on a flat surface.
Carefully peel back and put a crease along the
edge of the release liner ( Approximately 1 in or
25mm, Figure 1).
5. Press the foot pedal once, and then let it go while
slowly pulling the release liner as the board enters
the main roller nip (Figure 5)
Figure 5
6. Press the foot pedal once again when the board
has completely exited from the rear of the unit. Trim
the board if necessary.
Figure 1
2. With the image facing up, align the image onto the
board. Press firmly from the center out (Figure 2).
Figure 2
3. Adjust the pressure lever to ensure the proper
opening (Figure 3).
Figure 3
13
14
RSC-1400C/H
4. Disassemble the power switch bracket and place the left
rewinder outside of the frame; fasten with round head
3/16"(M5) screws (included in the option kit). Then,
reinstall the power switch bracket (Figure 7).
13. INSTALLATION OF FRONT FEEDER and REAR
REWINDER OPTIONS
Note: Below options are to be installed by an authorized RS reseller.
Figure 7
Figure 8
Figure 9
Installation of the Front Feeder Option (Includes 2 brackets,
one spindle, and mounting hardware).
5. Install the right rewinder on the outside of the frame and
connect the motor wire connector to the rear wire
(Figures 8 & 9).
1. Install the Front Feeder to the inside of the front frames
using four 1/4"(M6) hexagon bolts on each side (Figure 1)
Figure 1
6. Reinstall the rear cover.
Installing the Rear Rewinder Option (Includes motorized
winder, bracket, one spindle, and mounting hardware).
7. Reinstall the side covers.
1. Remove the left and right covers by using a Phillips
screwdriver (four screws on each side cover) (Figures 2 &
8. Reinstall the lever knob and screw.
Figure 2
Figure 3
3).
2. Remove the lever knob screw and lever (Figure 4).
Figure 4
3. Remove the rear cover by removing all
10 screws (4 top, 4 bottom, and 1 on
each side) (Figure 5 & 6).
Figure 5
Figure 6
15
16
RSC -1400C/H
14. MAINTENANCE
16. SPECIFICATIONS
Cleaning the Body of the laminaor
1. To clean the machine body, dampen a cloth with water only and gently wipe the machine clean.
Removing Adhesive Build Up
1. Remove the film from the laminator.
2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the
Teflon (metal) and silicone rollers.
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the
surface.Do not use sharp metal objects, steel wool, or abrasives, as these
may also damage the rollers.
Lubrication
1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or
heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever
comes first.
15. TROUBLESHOOTING
Problem
Cause
Solution
a. Plug the power cord into appropriate
outlet.
b. Put the power switch to the “I” (On)
position.
a. Power plug is not plugged in.
b. Power switch is in “0” (Off) position.
c. Tripped circuit breaker.
Machine will not turn
on:
d. Blown main power fuse.
c. Reset the circuit breaker.
d. Replace the fuse.
a. Emergency switch (es) is (are)
engaged.
b. Paper guide is not installed correctly.
There is power, but the
rollers are not turning
after the “RUN” button
is pressed:
a. Disengage the emergency switch (es).
b. Properly install the paper guide so that
the micro switch is activated.
c. Replace the motor fuse.
c. Blown motor fuse.
The unit is not heating
up:
a. Did not raise the temperature.
a. Raise the temperature.
a. Upward curl.
b. Downward curl.
a. Loosen the top roll film tension.
b. Loosen the bottom roll film tension.
Curled lamination:
17
18
|