Royal Sovereign Laminator RSH 380 User Guide

13. WARRANTY  
Royal Sovereign International warrants the equipment sold is free from defects in material  
and workmanship for a period of One (1) year for Parts and Labor from the date of  
installation, excluding lamination rollers which are warranted for Six (6) months. This  
warranty is extended only to the original purchaser. This warranty is the only warranty  
made by Royal Sovereign International and cannot be modified or amended. Royal  
Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy  
under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such  
defective part or product. These remedies are only available if Royal Sovereign’s  
examination of the product discloses to Royal Sovereign’s satisfaction that such defects  
actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized  
alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.  
OWNER'S MANUAL  
RSH-380 Laminator  
The warranty made herein is in lieu of all other warranties, expressed or implied, including  
any warranty or merchantability or fitness for a particular purpose. Royal Sovereign will not  
be liable for personal damage or personal injury (unless primarily caused by its  
negligence), loss of profit, or other incidental or consequential damages arising out of the  
use or inability to use this equipment.  
LIMITED WARRANTY  
This warranty specifically does not cover damage to laminating rollers caused by knives,  
razor blades, or any sharp objects or abrasives, or failure caused by adhesives, or  
damage caused by lifting, tilting and/or any attempt to position the machine other than  
rolling on the installed castors or feet on even surfaces, or improper use of the machine.  
Warranty repair or replacement by Royal Sovereign or its authorized Reseller(s) does not  
extend the warranty beyond the initial one year period from the date of installation.  
Unauthorized customer alterations will void this warranty.  
CORPORATE HEADQUARTERS  
Royal Sovereign International Inc.  
2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.  
TEL : +1) 800-397-1025  
FAX : +1) 201-750-1022  
E-mail : [email protected]  
RS Holland B.V.  
Columbusstraat 25 - 3165 AC Rotterdam,  
The Netherlands  
E-mail : [email protected]  
Royal Sovereign Inc. <Oversea Sales Office>  
1001, World Meridian II, 426-5, Gasan-dong,  
Geumcheon-gu, Seoul, 153-759, KOREA  
TEL : +82)2-2025-8800 FAX : +82)2-2025-8830  
E-mail : [email protected]  
Read all instructions carefully before use.  
For any Customer Support needs please choose the  
Customer Support tab on www.royalsovereign.com  
RS International Australia PTY. LTD.  
30 Prime Drive, Seven Hills, NSW 2147, Australia  
TEL : +61) 2-9674-2127  
FAX : +61) 2-9674-2027  
E-mail : [email protected]  
RS Canada Inc.  
164 Oakdale Road, Toronto, Ontario M3N 2S5  
CANADA  
Royal Sovereign International Inc.  
TEL : +1  
)
416-741-8400 FAX : +1 416-741-8185  
)
E-mail : [email protected]  
14  
 
RSH-380  
5. CONTROL PANEL  
3. SAFETY PRECAUTIONS  
Failure to comply with any of the following safety procedures could result in  
serious injury. Please read the instructions carefully and keep for future reference.  
1. Only a licensed electrician should install wiring and outlet for the laminator.  
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.  
3. Keep hands and clothing (i.e. Neckties) away from rollers.The rollers are pinch points  
that can trap body parts or clothing and cause serious injury.  
< TEMPERATURE >  
This button is for changing the temperature of upper and  
lower rollers,  
4. Keep flammable and wet objects away from the machine.  
5. Place machine on a level surface.  
Press the up button to increase temperature or the down  
button to decrease temperature.  
[range 20 oC(68 °F) through 150 oC(302 °F)]  
6. Avoid excessive sunlight, humidity and extreme temperatures.  
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving  
and/or repairing.  
8. Keep out of reach of children.  
9. Only Royal Sovereign authorized maintenance and service technicians should make  
repairs.  
< SPEED >  
10. Do not attempt to laminate items that exceed total recommended material thickness  
for the unit  
This button is used to change the speed of the rollers.  
(Settings 1 - 9)  
11. When cleaning the machine, don't use flammable sprays or materials.  
12. Do not touch the rollers when they are hot or place foreign objects inside the  
machine.  
< T-CHECK >  
13. Do not cover the surface of the machine until the machine has completely cooled.  
To Check current upper and lower roller temperature.  
Display automatically returns to previous settings after 5 blinks.  
4. PARTS  
< REVERSE >  
This button is used to reverse the rollers to undo jams and  
correct misfed documents.  
1.FILM-UPPER  
< RUN/STOP >  
2.FILM-LOWER  
3.TENSION CONTROL KNOB  
4.TOP HOT ROLLER  
5.FRONT FEED TABLE  
6.CONTROL PANEL  
7.SAFETY SHIELD  
8.PRESSURE LEVER  
This button is used to Run and Stop the machine.  
4
5
 
RSH-380  
6. FILM LOADING & THREADING  
< Film Threading >  
< Thermal Film Loading & Threading >  
Loading Film  
1. Remove the upper and lower film shafts from the  
machine and load the films (do not tighten the  
core screws at this time)  
2. To load the top film, insert 1" core as shown on  
Figure 1 (Note the direction of the film wound)  
Figure 1  
Figure 2  
Figure 3  
Figure 4  
Figure 5  
3. Insert the shaft as shown in Figure 2.  
1. Turn the power switch on (“I” position). (The Power  
switch is located on the rear the unit)  
4. Insert the core plug on the left hand side. Figure 3  
2. Complete the steps in the "Loading Film" section.  
3. Set the desired temperature.  
Figure 1  
4. Remove the Front Feed Table.  
5. Pull down the upper film over the Safety Shield to the  
lower film; align and center the lower film to the  
upper film and tighten the 2 lower bolt core  
screws. (Figure 1)  
5. Align and center the film and tighten the two core  
screws. Figure 4  
Figure 2  
Figure 3  
Figure 4  
6. Rewind the upper film until it aligns with the safety cover.  
7. Thread the film over the Lower Idle Bar and underneath  
the safety shield until the film rests on the upper  
roller. Figure 2  
8. Put the Front Feed Table back on and close the Safety  
Shield. Figure 3  
6. Repeat steps 2 through 4 to load the lower film.  
(Please note the direction of the  
film wound for the bottom roll). Figure 5  
9. Press the Run button and thread the film using the  
Laminating Threading Card. Figure 4  
7. Load the upper and lower film shafts on the machine.  
6
7
 
RSH-380  
7. BEFORE LAMINATING  
8. OPERATING INSTRUCTIONS  
1. For High Quality Lamination  
1. Turn the laminator on, the power switch is located  
- Refer to the "Recommended Temperature and Speed Settings" section before  
laminating.  
on the rear of the machine.  
2. Adjust the tension of the upper and lower films.  
Clockwise to tighten and Counter  
Clockwise to loosen.  
- The Upper and lower film tension must be same.  
2. Changing Roll film.  
3. Set the pressure lever to the "Laminating mode"  
4. Choose appropriate laminating temperature by  
pressing the "UP" or "DOWN" button.  
5. When desired temperature is met an alarm will  
sound and "READY" will appear on the  
display.  
- While laminating, if the roll film needs to be replaced, press the 'RUN/STOP'  
button .  
Once the rollers stop, cut the upper and lower film, remove and replace with new  
rolls of film.  
3. After lamination  
- “Hot Spots” on the rollers may occur when the machine is idle. To help prevent  
“Hot Spots”  
6. Press the "RUN/STOP" button. (If rollers don't run  
check that the safety shield is completely  
closed).  
you must run the sample paper between the front rollers and stop the machine  
while the sample paper is in between the rollers. You must leave the sample  
paper in this position until you laminate again.  
- After laminating with Thinflex™,use “Cleaning Paper” to clean the rollers.  
7. Position the item to be laminated on the Front Feed Table.  
8. Adjust the film tension or laminating speed if necessary.  
9.Press the "RUN/STOP" button when your l amination is finished.  
10.After finishing your work ,set the pressure lever to the "Hard Board/6mm"  
11.Turn the Power switch off  
NOTE:  
* Stand by mode : If no activity is made within 30 minutes after each use the  
machine will automatically switch to stand by mode.  
* Auto power off mode : If the machine is in standby mode and no activity is  
made for 90 minutes the machine will automatically power off.  
8
9
 
RSH-380  
9. RECOMMENDED TEMPERATURE AND SPEED SETTINGS  
1) The cross cutter is located on the rear exit table  
of the machine.  
speed Temperature Function  
Paper  
80 g/m2  
Paper(both side can be used)  
120g/m2  
100~110 oC  
4~5  
3~4  
25~38mic  
(1~1.5mil)  
(212~230 oF)  
200g/m2  
color paper  
2) After lamination, move the cutter approximately  
to the center of the application at the  
desired point of detachment.  
80g/m2  
Paper(both side can be used)  
120g/m2  
100~110 oC  
75mic(3mil)  
(212~230 oF)  
2~4  
4~5  
200g/m2  
color paper  
80g/m2  
Paper(both side can be used)  
3) Grasp film with one hand, press the cutter  
downward into he application and slide it  
first to one end of the application, then to  
the other end to complete the cut.  
100~115 oC  
100mic(4mil)  
(230~239 oF)  
120g/m2  
200g/m2  
color paper  
80g/m2  
2~3  
2~4  
120~125 oC  
(248~257 oF)  
Paper(both side can be used)  
120g/m2  
250mic(5mil)  
130~135 oC  
(266~275 oF)  
200g/m2  
2~3  
color paper  
10  
11  
 
RSH-380  
10. MAINTENANCE  
12. SPECIFICATIONS  
1. Do not apply any cleaning fluids to the rollers, certain fluids may cause damage.  
2. Do not clean rollers with sharp objects, use adhesive remover to clean resin off the  
rollers.  
Description  
Power supply  
RSH-380  
AC 100, 200, 220 240V 50/60Hz 120V 60Hz  
3. Use a damp cloth with only water to clean the body of the machine.  
4.Store machine in a dry clean area.  
Power consumption  
Max laminating width  
Film thickness  
1500W  
380mm / 15"  
25~250 mic / 1~10mil  
5m/min / 16.4ft/min  
8min  
11. TROUBLE SHOOTING GUIDE  
Max laminating speed  
Ready time  
Heating method  
Driving motor  
Hot roller  
Problem  
Possible Cause  
Possible Solution  
DC geared  
O
O
Max Temperature contro  
l
150 C / 302 F  
1. Check to make sure the  
safety shield is closed.  
1.Safety coveris opened.  
Rollers do not operate  
after the RUN/STOP  
button is pressed  
Speed control  
Transport type  
Film core size  
Cross cutter  
9 settings  
2. Power cord is not  
plugged in  
4 Roller  
2. Check the power cord.  
1", 2.25", 3"  
Yes  
Hot lamination  
Mounting thickness  
Reverse  
Yes  
Call your authorized  
dealer  
Call your authorized dealer  
Roller is not heating  
6mm / 0.24"  
Yes  
Unit dimensions (w  
Unit weight  
d
h)  
550 690 605(mm) / 21.5" 27" 24"  
45kg / 99 Ibs  
1. Film tension is  
unbalanced.  
1. Adjust film tension by  
rotating tension handle  
Carton dimensions (w  
Carton weight  
d
h)  
800 750 650(mm) / 31.5" 29.5" 25,5"  
57kg / 126 Ibs  
Result of lamination is  
waved.  
2. lower idler bar is not  
located in proper  
position  
2. Push idler bar up  
1. Adjust speed and  
temperature  
1. Temperature is lower or  
speed is higher than  
recommended  
Result of lamination is  
not clear  
12  
13  
 

Radio Shack Answering Machine TAD 704 User Guide
Ricoh Printer 1754 Express User Guide
Rotel Stereo Amplifier RB 991 User Guide
Rowenta Fan HA 425 User Guide
Samsung CRT Television WS32A11SP User Guide
Samsung Home Theater System AH68 02256G User Guide
Samsung Tablet 3 101 Gold Brown User Guide
SanDisk Camera Accessories SDDK 07 User Guide
Sanyo Cell Phone RL 4920 User Guide
Sennheiser Headphones 09920 User Guide