11. WARRANTY
Royal Sovereign International warrants the equipment sold is free from defects in material
and workmanship for a period of One (1) year for Parts and Labor from the date of
installation, excluding lamination rollers which are warranted for Six (6) months. This
warranty is extended only to the original purchaser. This warranty is the only warranty
made by Royal Sovereign International and cannot be modified or amended. Royal
Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy
under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such
defective part or product. These remedies are only available if Royal Sovereign’s
examination of the product discloses to Royal Sovereign’s satisfaction that such defects
actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized
alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.
OWNER'S MANUAL
RSL-380 Laminator
The warranty made herein is in lieu of all other warranties, expressed or implied, including
any warranty or merchantability or fitness for a particular purpose. Royal Sovereign will not
be liable for personal damage or personal injury (unless primarily caused by its
negligence), loss of profit, or other incidental or consequential damages arising out of the
use or inability to use this equipment.
LIMITED WARRANTY
This warranty specifically does not cover damage to laminating rollers caused by knives,
razor blades, or any sharp objects or abrasives, or failure caused by adhesives, or
damage caused by lifting, tilting and/or any attempt to position the machine other than
rolling on the installed castors or feet on even surfaces, or improper use of the machine.
Warranty repair or replacement by Royal Sovereign or its authorized Reseller(s) does not
extend the warranty beyond the initial one year period from the date of installation.
Unauthorized customer alterations will void this warranty.
CORPORATE HEADQUARTERS
Royal Sovereign International Inc.
2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.
TEL : +1) 800-397-1025
FAX : +1) 201-750-1022
E-mail : [email protected]
RS Holland B.V.
Columbusstraat 25 - 3165 AC Rotterdam,
The Netherlands
E-mail : [email protected]
Royal Sovereign Inc. <Oversea Sales Office>
1001, World Meridian II, 426-5, Gasan-dong,
Geumcheon-gu, Seoul, 153-759, KOREA
TEL : +82)2-2025-8800 FAX : +82)2-2025-8830
E-mail : [email protected]
Read all instructions carefully before use.
For any Customer Support needs please choose the
RS International Australia PTY. LTD.
30 Prime Drive, Seven Hills, NSW 2147, Australia
TEL : +61) 2-9674-2127
FAX : +61) 2-9674-2027
E-mail : [email protected]
RS Canada Inc.
164 Oakdale Road, Toronto, Ontario M3N 2S5
CANADA
Royal Sovereign International Inc.
TEL : +1
)
416-741-8400 FAX : +1 416-741-8185
)
E-mail : [email protected]
14
RHL-380
4. PARTS
3. SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result in
serious injury. Please read the instructions carefully and keep for future reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Keep hands and clothing (i.e. Neckties) away from rollers.The rollers are pinch points
that can trap body parts or clothing and cause serious injury.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving
and/or repairing.
8. Keep out of reach of children.
9. Only Royal Sovereign authorized maintenance and service technicians should make
repairs.
10. Do not attempt to laminate items that exceed total recommended material thickness
for the unit
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when they are hot or place foreign objects inside the machine.
13. Do not cover the surface of the machine until the machine has completely cooled.
1.Upper Film
4.Hot Rollers
7.Control Panel
2.Lower Film
5.Feed Table
8.Tension Knob
3.Idle Bar
6.Paper Guide
9.Power Switch
4
5
RSL-380
5. FEATURES GUIDE
6. OPERATION INSTRUCTIONS
Power Switch (1) - Located on the rear of
the machine. “I” (on) “0” (off). (Fig. 1)
Run and stop the machine
Cross Cutter (2) - Used to cut off the
laminated web. (Fig. 1)
Reverse the rollers to undo jams
and correct misfed documents
Figure 1
Figure 2
Figure 3
Figure 4
Feed Guide (3) -The feed guide permits
alignment of the item(s) to be laminated. To
position the adjustable guide, loosen the knob,
slide it to the desired position and tighten the
knob to secure the feed guide in place. (Fig.2)
Reduce roller speed
(1~10 speed settings)
Safety Shield (4) - It prevents entanglement
Increase roller speed
(1~10 speed settings)
NOTE: If the safety shield is opened, the power
to the motor will turn off.
Film Shaft and Locking
Core Adapter (5) -
25~38mic
(1~1.5mil)
The film shaft holds the film supply on the
machine. The locking core holds and locks the
film on the shaft to prevent shifting. (Fig.3)
Laminate 25~38mic (1~1.5mil) film
50~100mic
(2~4mil)
Laminate 50~100mic (2~4mil) film
Laminate 125mic (5mil) film
Film Tension Adjustment (6) - Allows the
operator to increase or decrease film web
tension. To increase the tension turn the knob
clockwise and to decrease tension turn the
knob counterclockwise. (Fig. 4)
125mic
(5mil)
6
7
RSL-380
1. Turn the laminator ON (I) located on the rear of the machine. (Fig. 1)
2. Choose appropriate laminating thickness and speed.
LOADING UPPER ROLL FILM
3. Do not begin laminating until the blinking light is steady (approximately 10 minutes).
4. Position the item to be laminated on the feed table.
5. Press the RUN button. The rollers will begin to turn, wait for heat line to disappear,
feed the item into the machine.
1.Slightly slide the shaft to the right and pull it out
from the machine.
6. Stop the laminator when all of the items have completely exited the rear of the
machine.
Repeat the above steps until all of your lamination is completed. When lamination is
completed or the machine is not in use for an extended period of time turn the power off.
Figure 1
Figure 2
Figure 3
NOTE: Stand by mode and auto power off mode
- Stand by mode: If no activity is made within 30 minutes after each use the machine
will automatically switch into stand by mode. (In stand-by mode the temperature will
decrease to 80~90°… (176~194°F) and the three film thickness setting indicators will
blink).
- Auto power off mode: If the machine is in stand by mode and no activity is
made for 60 minutes the machine will automatically power off.
- If any activity is made while in stand by or auto power off mode the machine
will return to it's previous settings.
2.Take both lock core adapters off of the shaft
7. FILM LOADING & THREADING
3.Insert one of the core adapters into the right end
of the film core. For film with poly-in (adhesive
side is inside the web), make sure the adhesive
side is facing upward.(Fig.3)
8
9
RSL-380
LOADING LOWER ROLL FILM
4. Insert the film shaft into the roll of film
from the right side with the copper end last.
Align and insert the core adapter on the left
end of the film core
1. Repeat steps 1-5 to load the lower roll film.
2. Once the upper and lower film is on the shaft, pull the film from the top and roll
down to the bottom roll to make certain that the film is aligned properly. Then
tighten the lower locking core screws.
NOTE: If the film is not aligned properly exposed adhesive will adhere to the rollers
and may cause the film to jam.
Figure 1
Figure 2
Figure 3
FILM THREADING
5. Center the film on the shaft and lock it in
place with the locking core adapters
Refer to Figure 6
8. MAINTENANCE
1. Do not apply any cleaning fluids to the rollers. Certain fluids may damage the
rollers.
6.Carefully return the film shaft back into place.
2. Do not clean rollers with sharp or pointed objects.
3. Use adhesive remover to clean resin off of the rollers.
4. Use a damp cloth with water to clean the body of the machine.
5. Store machine in a dry clean area
10
11
RSL-380
9. TROUBLE SHOOTING GUIDE
10. SPECIFICATIONS
Description
Power supply
RSL-380
Problem
Cause
Remedy
AC 100,200,220~240V 50 / 60Hz 120V 60Hz
Power consumption
Max laminating width
Film thickness
1200W
350mm / 14"
1.Safety cover is open
1. Check safety cover is
properly closed
Rollers do not operate
after the RUN/STOP
button is pressed
2. Power cord is not
plugged in
25~125 mic / 1~5mil
3m/min / 9.9ft/min
10 min
2. Plug in the power cord
3. Turn the machine on
Max laminating speed
Ready time
3.Machine is not turned on
Heating method
Driving motor
Hot Roller
DC geared motor
Digital(micom)
Call your authorized
dealer
Call your authorized dealer
Roller is not heating
Poor Lamination
Temperature contro
l
Speed control
Transport type
Cooling system
Side cutter
settings
10
1. Adjust film tension
1. Film tension is
unbalanced.
4 Roller
2. Push idler bar in proper
position
No
2. Lower idler bar is not
located in proper
position
No
Cross cutter
Yes
3. Follow manufacturers
recommended
temperature and speed
Film alignment
Hot lamination
Cold lamination
Reverse
No
3.Wrong temperature/
speed setting
Yes
No
Yes
Dimensions (w
Unit weight
d
h)
550 520 320(mm) / 21.7" 20.5" 12.6"
30kg / 66.1Ibs
12
13
|