SECO LARM USA Security Camera EV 2166 N3WQ User Guide

Mid-Size Vandal Dome Camera  
Manual  
(3.6mm model shown)  
Model No.  
Resolution  
Lens Size  
# of IR LEDs  
NTSC  
EV-2166-N3WQ  
EV-2166-NVWQ  
EV-2766-N3WQ  
EV-2766-NVWQ  
420 TV lines  
420 TV lines  
540 TV lines  
540 TV lines  
3.6mm  
4~9mm  
3.6mm  
4~9mm  
18  
21  
18  
21  
PAL  
EV-2166-P3WQ  
EV-2166-PVWQ  
EV-2766-P3WQ  
EV-2766-NVWQ  
420 TV lines  
420 TV lines  
540 TV lines  
540 TV lines  
3.6mm  
4~9mm  
3.6mm  
4~9mm  
18  
21  
18  
21  
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.  
 
SECO-LARM Mid-Size Vandal Dome Cameras  
Overview:  
Models ending in  
NVWQ or PVWQ only.  
Focus  
Zoom  
Camera  
Set screw  
Dome cover  
Female BNC connector  
DC plug with  
Wiring notch  
terminal block  
DC jack  
Important:  
Do not cut the DC jack or  
the female BNC connector  
as this will void the  
warranty.  
Mounting base  
Mounting screw  
Before Starting:  
1. Please read this manual carefully and keep it for future  
reference.  
5. Do not drop the camera or subject it to strong  
vibrations.  
2. Use the camera within given temperature and electricity  
limits.  
3. Do not point the camera at the sun. Heat could damage  
the camera, even when not in use.  
4. Do not mount the camera in areas exposed to radiation,  
strong magnetic fields, or strong electrical signals*  
Note: Many video monitors produce strong  
electromagnetic fields close to the display CRT,  
especially when the monitor is turned on or during  
de-gaussing, which occurs automatically with many  
monitors when turned on.  
Installation:  
1. Run hidden cables from the video source and 12VDC  
power supply to the camera. Do not cut the DC jack or  
the female BNC connector as this will void the  
warranty. If needed, use the included SECO-LARM  
DC plug with terminal block.  
6. Mount the mounting base to the wall using the 3  
included mounting screws. If necessary, use the  
included screw anchors.  
7. Adjust the camera angle as shown on page 2,  
Adjusting the Camera Angle.  
8. Test the video signal.  
2. Test to make sure the voltage is correct.  
Use only 12VDC.  
9. Models ending in NVWQ and PVWQ only: Adjust  
the zoom and focus by hand or with a small  
screwdriver to loosen the knob, and then sliding the  
knob left or right. IMPORTANT: Do not use power  
tools. Lens damage may result.  
3. Undo the 3 set screws on the side of the dome cover  
using the included allen wrench and remove the dome  
from the base.  
4. Hold the camera against the wall, ceiling, or other  
mounting surface while watching the monitor to find the  
best mounting location. Mark that location with a pencil.  
5. If the installation involves surface wiring, use the wiring  
notch located on the side of the mounting base  
to run wires.  
10. Reattach the dome to the camera.  
11. Use the included allen wrench to tighten the set  
screws, securing the dome to the base.  
12. Do a final test of the video camera and monitor.  
SECO-LARM U.S.A., Inc.  
3
 
SECO-LARM Mid-Size Vandal Dome Cameras  
Troubleshooting:  
Check that the camera is powered up.  
Check that the power supply’s polarity is correct.  
Check that the monitor is powered up.  
The screen is blank.  
Check that the video cable connecting the camera to the  
monitor is connected properly.  
Clean the lens using a soft, clean cloth.  
Check that the light source is adequate.  
The screen image is dim  
Adjust the monitor’s contrast knob.  
Change the position of the camera.  
The screen image has poor contrast.  
Change the position of the camera.  
Change the position of the camera.  
The screen image flickers.  
The screen image is distorted.  
The camera case is hot.  
IR LEDs do not turn on.  
Check that the correct power supply is in use.  
Check that the correct power supply is in use.  
IMPORTANT  
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and  
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this  
product in violation of any current laws or statutes.  
WARNING  
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open  
the case of this device, as there are no field-serviceable components inside.  
FCC COMPLIANCE STATEMENT  
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to  
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the  
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to  
correct the interference at his or her own expense.  
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a  
period of one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of  
any defective part if the unit is returned, transportation prepaid, to SECO-LARM.  
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or  
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is  
not operating properly as a result of causes other than defects in material and workmanship.  
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at  
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or  
property damages of any kind to the purchaser or anyone else.  
NOTICE  
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is  
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without  
notice. SECO-LARM is also not responsible for misprints or typographical errors.  
Copyright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,  
without the written permission of SECO-LARM.  
SECO-LARM U.S.A., Inc.  
16842 Millikan Avenue, Irvine, CA 92606  
Tel: 800-662-0800 / 949-261-2999  
PICSN4  
MiEV-2x66-xxWQZZ_1011.docx  
4
SECO-LARM U.S.A., Inc.  
 

Q Logic Router ISR6260 User Guide
Quantum Stereo Amplifier QT600 User Guide
Radio Shack Cordless Telephone ET 537 User Guide
Roberts Radio Clock Radio CR9945 User Guide
Ryobi Saw TS1301 User Guide
Samsung DVD VCR Combo SV 9000W User Guide
Sanyo Battery Charger N 100AAS User Guide
Sanyo Flat Panel Television PLV 55WM1 User Guide
Senco Staple Gun SLS20 SLS25 User Guide
Sennheiser Headphones HD 515 User Guide