Salton Juicer JE 1013 User Guide

®
Professional  
juice extractor  
Instruction Booklet  
Model: JE-1013  
 
18. Always make sure the juicer is fully assembled and the juicer cover  
is locked securely in position before the motor is turned on.  
Do not attempt to remove parts when the juicer is in operation.  
19. Do not attempt to override the safety features.  
20. Do not use this appliance if the strainer basket is damaged.  
21. Do not put your fingers or other objects into the feed tube while it is  
operating. Always use the food pusher provided. If food becomes lodged  
in the feed tube use the food pusher or another piece of fruit or vegetable  
with the food pusher to push it down. If this is not possible, turn  
the motor off and unplug the unit from the wall outlet and disassemble  
the unit to remove the stuck food.  
22. Do not place on or near a hot gas or electric burner, or in a heated oven.  
23. Always attach plug to appliance first, then plug cord into the wall outlet.  
To disconnect, turn any control to ‘OFF’, then remove plug from wall outlet.  
SAVE THESE INSTRUCTIONS  
HOUSEHOLD USE ONLY  
GROUNDED PLUG  
To reduce the risk of electric shock this appliance has a grounded plug.  
(2 blades and 1 pin) If the plug does not fit fully into the electrical outlet  
contact a qualified electrician. Do not modify the plug in any way  
or use an adaptor.  
BEFORE FIRST USE  
1. Read the instructions carefully and keep for future reference  
2. Remove all packaging.  
3. Disassemble the juicer (see the Care and Cleaning section).  
Wash all removable parts to remove any residue left over from  
the manufacturing process.  
3
 
DESCRIPTION OF PARTS  
8
1. Motor Housing  
2. Electronic Control  
A - Hi speed  
B - Off  
6
7
4
C - Lo speed  
10  
3. Locking handle  
4. 1.5 litre/quart pulp container  
9
13  
5. Pulp Container Safety Foot  
(Not Shown)  
11  
6. Pulp Chute/Juicer Cover  
7. Feed Tube  
8. Food Pusher  
9. Stainless Steel Juice Collector  
10. Stainless Steel Strainer  
Basket/Cutting Blades  
3
1
5
2
12  
11. Spout  
14  
12. Juice Jug  
13. Froth Separator (inside jug)  
14. Rubber feet  
4
 
HOW TO ASSEMBLE THE JUICER  
1. Place the Stainless Steel Juice collector on  
the motor housing with the spout facing  
the direction of the Locking Handle. Swivel until  
it locks into place. (See Ill. 1)  
2. Place the Stainless Steel Strainer Basket inside  
the Juice Collector. Twist the Strainer Basket  
and gently push down until it is seated  
in the Juice Collector. (See Ill. 2)  
Ill.1  
NOTE: The top edge of the Strainer Basket  
should not be higher than the edge of  
the Juice Collector when properly installed.  
3. Place the Pulp Chute/Juicer Cover on the top so  
that the opening of the Pulp Chute is on the  
side opposite the spout. (See Ill. 3)  
Ill. 2  
Ill. 3  
Ill. 4  
4. Lock the Pulp Chute/Juicer Cover into position  
by raising the Locking Bar until it clicks into  
the grooves located on both side of the Pulp  
Chute/Juicer Cover. (See Ill. 4)  
NOTE: Push the Locking Bar until it is fully  
upright otherwise the Juicer will not operate.  
5. Align the groove in the Food Pusher with the  
small protrusion on the inside of the Feed Tube.  
6. Slide the Pulp Container into position under  
the Pulp Chute. Ensure that the Safety Foot  
on the Pulp Container is fully inserted in the slot  
in the Motor Housing otherwise the Juicer  
will not operate.  
7. If the Froth Separator is not in the Juice Jug,  
slide between the tabs inside the Juice Jug.  
If you prefer to have juice with froth then  
the Froth Separator is not required.  
8. Place the Juice Jug or a glass under the spout.  
5
 
HOW TO PREPARE FRUIT AND VEGETABLES FOR JUICING  
1. Wash fruits and vegetables.  
2. Peel fruits that have inedible skins such as citrus fruits, pineapple,  
melons, papaya, etc.  
3. Pit all fruits with hard seeds or stones such as peaches, nectarines,  
cherries, etc.  
4. Most fruits and vegetables such as apples, carrots and cucumbers will  
not need to be cut. If the pieces are too big for the Feed Tube, slice  
the fruit or vegetables before starting to juice.  
HOW TO JUICE  
1. Assemble the Juicer. The Juice Jug or a glass can be placed below  
the pout to collect juice.  
2. Plug the power cord into a 120 V power outlet.  
3. Choose either ‘Hi’ or ‘Lo’ speed on the Electronic Control depending  
on the type of fruit or vegetable that is being juiced. Never put any fruit  
or vegetables in the juicer until power is turned on. Soft fruit or  
vegetables, such as berries, melons, cucumber, tomatoes, etc. should  
be juiced on Lo speed. Harder fruit and vegetables such as apples, celery,  
carrots, etc. should be juiced at ‘Hi’ speed.  
4. With the motor running, place food into the Feed Tube. Using the Food  
Pusher, gently guide food down the Feed Tube. To Extract the maximum  
amount of juice, always push the Food Pusher down slowly.  
IMPORTANT: DO NOT PLACE HANDS OR FOREIGN OBJECTS DOWN  
THE FEED TUBE. ALWAYS USE THE FOOD PUSHER  
5. If the Pulp Container is full it can be emptied during juicing. Turn  
the Juicer Off and remove the Pulp Container by holding onto the Feed  
Tub and tilting the juicer slightly to disengage the Safety Foot on the Pulp  
Container. Empty the Pulp Container. Replace by sliding the Pulp  
Container into position under the Pulp Chute. Ensure that the Safety Foot  
on the Pulp Container is engaged in the slot in the Motor Housing.  
6
 
6. The froth separator in the Juice Jug will eliminate froth being poured into  
the glass. If you prefer to have juice with froth, simply remove the froth  
separator attachment from the Juice Jug before juicing  
IMPORTANT: When juicing on ‘Hi’ Speed do not run the Juicer  
for longer than 5 minutes then allow to rest for 2 minutes  
before you resume juicing.  
HELPFUL HINTS  
A small amount of lemon juice can be added to apple juice  
to prevent browning.  
Do not use bananas or avocados as they do not contain juice and will  
clog the juicer.  
Allow the juicer to run for one minute before turning ‘Off’ to allow  
any excess juice to be extracted from the pulp.  
A plastic bag can be put in the pulp container for easy clean-up.  
Disassemble the Juicer and rinse off the pulp immediately after juicing.  
The Strainer Basket/Cutting Blades can be soaked in water to loosen  
the pulp. Then wash in warm soapy water.  
Wash parts immediately after use to avoid discolouration of the plastic  
parts which may occur with some fruits and vegetables.  
If juicing herbs or leafy green vegetables process in combination with  
other fruits or vegetables to yield more juice.  
7
 
CARE AND CLEANING  
How to Disassemble the Juicer  
IMPORTANT: Before disassembling the Juicer make  
sure that the Electronic Control is in the Off position,  
the plug has been removed from the wall outlet  
and the motor has stopped completely.  
1. Remove the Food Pusher from the Feed Tube.  
2. Remove the Pulp Container by holding onto  
the Feed Tube and tilting the juicer slightly to  
disengage the Safety Foot on the Pulp Container.  
3. Remove the Juice Jug.  
4. Hold the Pulp Chute/Juicer Cover and disengage  
the Locking Bar from the grooves on the side  
of the Pulp Chute/Juicer Cover. (See Ill. 1)  
Ill.1  
5. Lift and remove the Pulp Chute/Juicer Cover.  
(See Ill. 2)  
6. Remove the Stainless Steel Juice Collector  
and Strainer Basket by placing one hand under  
the spout and the other under the black plastic  
edge opposite the spout and lifting upwards.  
The Stainless Steel Strainer Basket can be removed  
from the Juice Collector by pushing it up through  
the hole in the bottom of the Juice Collector.  
Ill. 2  
NOTE: Be careful when handling the Strainer  
Basket as the cutting blades are very sharp.  
8
 
How to Clean  
1. Move the Control Switch to the Off position and wait for the motor  
to stop completely.  
2. Unplug from the wall outlet.  
3. Disassemble the Juicer (see directions on page 8)  
4. Clean the Pulp Container, Pulp Chute/Juicer Cover, Food Pusher, Stainless  
Steel Juice Collector, Juice Jug and Froth Separator in warm, soapy water.  
A mild detergent is recommended. Rinse well and dry thoroughly.  
NOTE: Care must be taken when cleaning or storing the Pulp  
Container with Safety Foot.  
5. Hold the Stainless Steel Strainer Basket/Cutting Blades under clean  
running water. Use the cleaning brush included with the Juicer to gently  
clean away pulp from the filter and cutting blades. Rinse under running  
water. Hold the Strainer Basket/Cutting Blades up to the light to ensure  
that the fine mesh holes are not blocked. If the holes are blocked, soak  
the Strainer Basket/Cutting Blades in hot water to loosen the pulp and  
clean with the nylon brush again. Allow to dry on a cloth or paper towel  
before reassembling the juicer.  
CAUTION: THE CUTTING BLADES ARE VERY SHARP.  
6. Wipe the Motor Housing with a soft cloth moistened in warm soapy  
water. NEVER IMMERSE MOTOR HOUSING WATER OR ANY  
OTHER LIQUID.  
9
 
TROUBLESHOOTING  
Problem  
Solution  
Juicer will not operate  
when switched on.  
•The safety locking arm may not be  
correctly engaged into the 2 grooves  
on either side of the Pulp  
Chute/Juicer Cover.  
•The safety foot is not fully inserted  
in the slot in the Motor Housing.  
Motor stalls when juicing  
•Push the Food Pusher down slowly  
so that wet pulp does not build up  
under the Pulp Chute/Juicer Cover.  
•Choose Hi speed instead of Lo speed.  
Excess pulp building up in filter  
Pulp too wet  
•Alternate soft and hard fruit  
and vegetables  
•Use Lo speed.  
•Check to be sure that the holes in  
the mesh filter are not blocked. If  
they are blocked follow #5 in the  
How to Clean section.  
Juice leaks between the rim of the •Use Lo speed. Fruits and vegetables  
Juicer and Pulp Chute/Juicer Cover  
with a high water content should be  
juiced on Lo speed.  
10  
 
JUICE RECIPES  
Below are a few juice recipes for your convenience. Additional recipes are  
available on the internet. Recipe books are also available at your local bookstore.  
Apple Strawberry  
5
1
apples  
cup strawberries  
Alternate juicing apples and strawberries. Serve immediately.  
Apple Veggie Juice  
2
3
1
apples  
carrots  
stalk celery  
Alternate juicing apples, carrots and celery. Serve immediately.  
Vegetable Juice  
4
carrots  
2 ozs. (100 g)  
spinach  
1
2
Small handful of flat leaf parsley  
stalks celery  
Alternate juicing above ingredients. Serve immediately.  
Fruit & Vegetable Cocktail  
1/2  
1
pineapple, peeled  
carrot  
1
apple  
1
stalk celery  
Process through juicer and serve immediately.  
Peach, Pear and Apple Juice  
1
2
1
apple  
peaches, seed removed  
pear  
Process ingredients through juicer and serve immediately.  
11  
 
A short supply cord is provided to reduce the hazards of becoming entangled  
in or tripping over a long cord. Extension cords may be used if care is exercised  
in their use. If an extension cord is used, the marked electrical rating of the  
detachable power-supply cord or extension cord should be at least as great as  
the electrical rating of the appliance. If the appliance is of the grounded type,  
the extension cord should be of a grounded 3-wire cord. The extension cord  
should be arranged so that it will not drape over the counter top or table top,  
where it can be pulled on by children or tripped over.  
LIMITED  
WWARRANTY  
Toastess International warrants that this appliance shall be free from defects in material  
and workmanship for a period of one year from the date of purchase. During this  
’in-warranty’ period, defective products will be repaired or replaced at the discretion  
of the retailer and/or Toastess International. A defective product should be returned to  
the original place of purchase within the retailer’s stipulated return/exchange period*.  
If you are unable to have a defective product replaced under warranty by the retailer,  
Toastess International will repair or replace the defective product without charge. You  
may contact us for assistance by mail, e-mail, fax or telephone as listed below.  
This warranty covers normal domestic usage and does not cover damage which occurs  
in shipment or failure which results from alteration, accident, misuse, abuse, glass  
breakage, neglect, commercial use or improper maintenance.  
To ensure prompt ’in-warranty’ service be sure you have an original proof of purchase.  
You may be asked to return the product to us along with a description of the defect  
and your address, zip/postal code.  
For repairs not covered by the warranty, please contact us for assistance.  
®
SALTON CANADA  
Customer Service Department  
81A Brunswick  
Dollard-des-Ormeaux  
Quebec, Canada H9B 2J5  
Fax: 514-685-8300  
Tel: 514-685-3660  
* Return/exchange policies at each retailer vary and may differ from the Salton Canada 1 year limited  
12  
warranty period.  
 

Radica Games Handheld Game System 74037 User Guide
Radio Shack Battery Charger 23 249 User Guide
Radio Shack Portable Radio 12 795 User Guide
Ricoh Digital Camera R 3 User Guide
Ryobi Cordless Saw RJC180 User Guide
Sakar Digital Camera 16382 User Guide
Samsung Digital Camera AD68 04519A User Guide
Samsung Printer ML 2240 User Guide
Savin Printer 3310L User Guide
Sears Automobile Battery Charger 2871222 User Guide