Samsung Washer Dryer SW 903P User Guide

WASHING MACHINE  
Owner’s Instructions  
SW-903(P)/SWT90C1(P)/SWT90C2(P)  
BEFORE USING THE WASHING MACHINE 1  
PRECAUTIONS  
CONTROL PANEL  
1
2
DESCRIPTION AND CLEANING OF PART 2  
WASHING PROCEDURE  
To Wash  
To Spin Dry  
To Rinsing  
Overflow rinse  
Additional rinse  
INSTALLATION  
Location  
Mounting the legs  
Connecting the drain hose  
Changing the position of the drain hose  
LAUNDRY GUIDE  
MAINTENANCE  
TROUBLE SHOOTING  
3
3
3
4
4
4
5
5
5
5
5
5
6
6
Before operating the washing machine, please read this manual  
thoroughly, and retain it for future reference.  
 
CONTROL PANEL  
BEFORE USING THE WASHING MACHINE CAUTIONS  
0
Remove the cap-hose  
from the drain hose.  
Be sure that the washer is grounded.  
To avoid electrical shock,use a  
metal pipe for the ground  
1.  
WASH TIMMER  
This is used to set the  
wash time, 1-15 minutes.  
15  
12  
3
6
9
connection. But, don't ground the  
washer with gas pipes or telephone  
lines to avoid to dangers of explosion  
or lightning strike.  
WASH TIMER  
In the case of pump drained  
washer, remove  
the cap-hose from  
the drain hole.  
2.CYCLE SELECTOR  
This is used to set the  
Washing/Rinsing  
or Draining.  
Wash/Rinse  
Wash  
Drain Rinse  
Drain  
CYCLE SELECTOR  
CYCLE SELECTOR  
Do not put your hands into the  
spin dryer basket when it is  
spinning.  
Your fingers can be caught by  
spinning laundry and damaged.  
0
3.  
SPIN DRY TIMER  
5
4
1
2
This is used to set the  
spin time, 1-5 minutes.  
PRECAUTIONS WHEN OPERATING  
3
SPIN DRY TIMER  
SELECTOR  
4.WATER  
Don't use excessively hot water.  
(50˚C or more)  
Plastic parts may be deformed or damaged.  
Also, clothing may be deformed or decolored.  
Never allow children to operate  
or play with the washer.  
Children playing with the  
washer may accidentally  
fall into the washing tub.  
During washing, WATER SELECTOR  
KNOB should be selected.  
During spin rinsing, WATER  
SELECTOR KNOB should  
be selected.  
Wash  
Spin  
WATER SELECTOR  
Before washing,check all pockets.  
If nails or pins remain in pockets,they may  
damage the washer or clothes.  
Disconnect the power cord from the  
power supply when not in use.  
5
SELECTOR(CONTROL)  
Normal Normal  
.WASH  
Delicate  
(LITE)  
Heavy  
Soft  
Heavy  
Close the water tap a little if the  
water pressure is too high.  
Ventilation opening must not be obstructed  
by carpeting when the washing machine is  
installed on a carpeted floor.  
WASH CONTROL  
WASH SELECTOR  
This is used to select wash action.  
You can wash laundry effectively  
by various methods.  
Never splash water on the control panel.  
If the supply cord of this appliance is  
damaged, it must only be replaced by a repair  
shopappointed by the manufacturer, because  
special purpose tools are required.  
Be sure to cover with the inner  
cover on laundry before spinning.  
This prevents laundry from  
Drain  
Wash  
6
7
.DRAIN SELCTOR  
Be sure to press the selector  
knob to “WASH” while washing.  
DRAIN SELECTOR  
being tossed out and damaged.  
Warning to avoid overfilling and damages this  
appliance must be filled with the operator  
present using a moderate water supply  
pressure only.  
To avoid water splashes, close the  
wash tub lid.  
.WATER INTAKE  
Connect water inlet to  
a tap with a suitable.  
WATER INTAKE  
Be sure laythe drain hose down.  
(in case no drain pump)  
Do not store or use gasoline or other flammable  
vapors and liquids in the vicinity of this or any  
other appliance.  
To avoid overfilling and damages this appliance  
must be filled with the operator present using a  
moderate water supply pressure only.  
 
1
DESCRIPTION AND /CLEANING OF PARTS  
CLEANING THE FILTER  
Pull the overflow filter out and take up  
the filter by removing 3 screws as  
shown in figure. Wash the filter and  
washing tub.  
SPIN DRYER LID  
When you open this  
INNER LID  
lid while the spin basket is  
spinning,the spinning will  
be stopped by the brake  
system.  
DRAIN HOSE  
CLEANING THE FILTER  
SPIN DRYER BASKET  
(with pump)  
Push the strainer(filter) out and take  
up the filter as shown in figure.  
Wash the filter and washing tub.  
POWER CORD  
The plugs shape  
may not be similar to that  
shown in this drawing.  
OVERFLOW  
FILTER  
LINT FILTER  
This is used for  
gathering the  
dregs made  
during washing.  
DRAIN FILTER  
In case of incomplete drain,  
disassemble the drain filter with  
screw driver(+), and remove  
lints from the filter as shown  
in the filter as shown in  
the figure.  
WATER DRAIN HOSE  
(without pump)  
WASH TUB LID  
Be sure to keep  
the lid closed  
EARTH WIRE  
during washing  
and spinning.  
HOW TO CLEAN THE FILTER  
(In case drain pump)  
1. Place a rag under the washer filter  
not to wet the floor.  
2. Rotate the filter counterclockwise  
and pull out the filter.  
WASH TUB  
PULSATOR  
DRAIN FILTER  
CONTROL LEG  
3. Remove dirts and  
rotate the filter  
clockwise until it  
locks in position.  
CLEANING THE LINT FILTER  
If the dregs are piled up in the  
lint filter after finishing the wash,  
push down and  
OVERFLOW FILTER  
Pull the upper side of the  
overflow filter with your  
fingers into the holes  
in the direction of  
OVERFLOW FILTER  
Pull the upper side of the  
overflow filter with  
two fingers inserted into  
hole Ain the  
A
pull it out as  
direction of arrow  
shown in the  
arrow as shown  
as shown in the figure.  
figure.  
in the figure.  
Wash the filter  
net in water.  
CLEANING THE WASH TUB  
First, fill water in the wash tub to Llevel(  
, then drain water from the wash tub simultaneously with  
operating wash cycle for 1~2 minutes. Close the wash tub lid.  
 
2
WASHING PROCEDURE  
A-type : SWT90C1(P)/SWT90C2(P)/WT10S0(P)/WT10S1(P)/WT10S2(P)  
B-type : SW-903(P)  
TO WASH (A-type)  
TO WASH (B-type)  
TO SPIN DRY  
1. Before starting to wash, proceed as follows,  
Connect the water supply hose and open  
the water tap.  
1. Before starting to wash, proceed as follows,  
Connect the water supply hose and open  
the water tap.  
1. Transfer the clothes into the  
spin basket and arrange the  
clothes evenly.  
Lay the drain hose down toward  
a sinkhole. (In case no drain pump)  
Place the drain hose in sink or bath.  
(In case no drain pump)  
Connect the power cord to the power  
supply outlet.  
Lay the drain hose down toward  
a sinkhole. (In case no drain pump)  
Place the drain hose in sink or bath.  
(In case no drain pump)  
Connect the power cord to the power  
supply outlet.  
2. Be sure to replace the safety  
cover and close the  
inner lid  
inner lid.  
safty cover  
Normal  
2. Set the CYCLE SELECTOR KNOB to  
2. Select the WASH  
Delicate  
(LITE)  
Heavy  
WASH.RINSE.(in case drain pump WASH)  
CONTROL KNOB  
for desired mode.  
Wash/Rinse  
Wash  
3. Close the spin  
dryer lid.  
WASH CONTROL  
DRAIN WASH  
Drain Rinse  
Drain  
3. Press the  
DRAIN SELECTOR KNOB  
to WASH.  
CYCLE SELECTOR  
CYCLE SELECTOR  
Wash  
Spin  
DRAIN SELECTOR  
3. Set the WTER SELECTOR  
KNOB to the desired mode.  
WATER SELECTOR  
4. Fill water in the wash tub  
and add the detergent.  
4. Set the SPIN DRY  
TIMER 1-5 minutes.  
0
3
5
4
1
2
4. Set the WASH SELECTOR  
KNOB to the desired mode.  
5. Load laundry in the  
wash tub and fill water  
to proper water level.  
SPIN DRY TIMER  
5. Fill water in the wash tub  
and add the detergent.  
0
6. Set the WASH TIMER  
1-15 minutes.  
15  
12  
3
6
6. Load laundry in the  
wash tub and fill water  
to proper water level.  
9
7. After washing Press the  
DRAIN SELECTOR KNOB to  
DRAINfor drain.  
WASH TIMER  
DRAIN  
WASH  
7. Set the WASH TIMER  
1-15 minutes.  
0
15  
12  
3
6
DRAIN SELECTOR  
8. After washing, set the CYCLE  
SELECTOR KNOB to  
9
WASH TIMER  
'DRAIN' for drain.  
 
3
ADDITIONAL RINSE  
TO RINSING (A-type)  
OVER FLOW RINSE (A-type)  
Wash/Rinse  
Wash  
1. Keep supplying  
1. Set the cycle selector KNOB to  
WASH.RINSE.  
1 After rinsing you can select this  
course for more effective rinse  
(Don't just select this course  
for rinse.) Load the laundry  
evenly into the spin basket.  
Wash/Rinse  
Wash  
water(adjust water  
pressure to ensure  
that the amount of  
Drain Rinse  
Drain  
(In the case of drain  
Drain Rinse  
Drain  
pump WASH)  
CYCLE SELECTOR  
CYCLE SELECTOR  
water supplied  
CYCLE SELECTOR  
CYCLE SELECTOR  
does not exceed the amount  
of water drained.)  
2. Supply the proper amount of water  
so as not to delete one space overflow  
the top of the washing tub.  
0
2 Set the WATER SELECTOR  
KNOB to SPIN and  
15  
12  
3
6
0
9
2. Set the WASH TIMER  
6~8 minutes.  
CYCLE SELECTOR  
Wash  
Spin  
15  
3
6
9
KNOB to DRAIN.  
WASH TIMER  
3. Set the WASH TIMER to  
2~3 minutes.  
WATER SELECTOR  
0
12  
15  
3
3. As soon as the  
WASH TIMER  
shuts off, turn off  
the water tap.  
3 Supply water for about 1 minute.  
Adjust the water flow to prevent  
overflow from the wash tub.  
WASH TIMER  
12  
4. Drain the water.  
6
9
Set the delete one space cycle  
selector KNOB to DRAIN.  
WASH TIMER  
4 After completing the water supply,  
4. Set the CYCLE  
SELECTOR KNOB  
to DRAIN.  
cover the laundry with  
safety cover and close safety  
the inner lid.  
inner lid  
5. Repeat this cycle until drain  
water is clean. (2~3 cycles)  
cover  
OVER FLOW RINSE (B-type)  
TO RINSING (B-type)  
5 Close the spin dryer lid.  
1. Keep supplying  
water(adjust water  
pressure to ensure  
that the amount of  
water supplied  
DRAIN  
WASH  
1. Press the DRAIN SELECTOR  
0
6 Set the SPIN DRY  
TIMER 2~3 minutes.  
KNOB to WASH.  
5
1
2
DRAIN SELECTOR  
4
2. Supply the proper amount  
of water so as not to  
3
SPIN DRY TIMER  
does not exceed the amount  
of water drained.)  
0
delete one space overflow  
the top of the washing tub  
and put the laundry  
15  
3
0
12  
6
2. Set the WASH TIMER  
6~8 minutes.  
15  
12  
3
6
9
into the washing tub.  
WASH TIMER  
0
3. Set the WASH TIMER  
2~3 minutes.  
9
15  
3
WASH TIMER  
3. As soon as the  
WASH TIMER  
shuts off, turn off  
the water tap.  
12  
6
9
DRAIN  
WASH  
WASH TIMER  
4. Drain the water.  
Set the DRAIN SELECTOR  
KNOB to DRAIN.  
DRAIN  
WASH  
DRAIN SELECTOR  
4. Press the DRAIN SELECTOR  
KNOB to DRAIN.  
DRAIN SELECTOR  
5. Repeat this cycle until drain  
water is clean. (2~3 cycles)  
 
4
INSTALLATION  
LAUNDRY GUIDE  
LOCATION  
Leave some space of  
at least 15cm between the washing machine drain hose(b) in the draining direction.  
and the wall.  
Place the washing machine on a sturdy flat  
surface.  
If the washing machine is placed on an uneven  
or weak surface, noise or vibration may occur.  
(Allowable is 2˚)  
CONNECTING THE DRAIN HOSE  
WASHING TIME  
After attaching the connector ring(a), insert the  
Water Level  
Low  
Middle  
High  
22 Pieces 29 Pieces 35 Pieces  
38 Pieces 48 Pieces 58 Pieces  
16 Pieces 20 Pieces 25 Pieces  
Sgurts (Synthetics)  
a
b
Under Shirts (Cotton)  
Workign clothes (Cotton)  
Never install the washing machine near water. CONNECTING THE DRAIN HOSE  
Do not place the washing machine in steamy room or 1. Before connecting the drain hose, remove  
SPIN DRY TIME  
where the washing machine is directly exposed to  
the cover (a) from the drain hole.  
TYPE OF FABRIC  
Thin (synthetic fiber)  
TIME  
1 min.  
rain. Moisture may damage electrical insulation 2. After pressing the joint ring (b), insert the  
and cause an electrical shock to occur.  
Avoid direct sunlight or heating devices.  
As plastic and electrical components are  
affected by direct heat, never place the washing  
machine near heaters, boilers, etc., or under direct  
sunlight.  
drain hose(c) to drain direction.  
wool  
cotton  
1~2 min.  
3~5 min.  
5 min.  
thick (cotton)  
(a)  
(C)  
(C)  
(b)  
(b)  
DETERGENT  
(In case of pump  
drained washer)  
WATER  
LEVEL  
AMOUNT OF  
DETERGENT  
The amount of detergent  
is average. Follow the  
instruction printed on the  
package for amount of  
detergent. Choose the  
amount of detergent  
Install the drain hose  
about 70~80cm above  
the ground for pump model.  
Low (44l)  
44g  
56g  
67g  
CHANGING THE POSITION OF THE  
DRAIN HOSE  
Before attempting to change the position of the  
Medium (56l)  
High (67l)  
MOUNTING THE LEGS  
drain hose, disconnect the plug from the outlet.  
1. Route the drain hose inside the machine.  
2.Take out the drain hose from the opposite hole  
and insert the drain hose into the hose holder.  
according to the fabric type.  
Lay down the washer with its back facing  
downward. Insert four legs into the leg mounting  
DETERGENT  
In case the water level is at High,  
amount of water is 42l.  
Claw  
sections of the base corners of the main body.  
Square  
hole  
-H-  
Insert the claw of the  
leg with the square  
hole of the leg  
2
1
Follow the directions printed on the package  
for amount of detergent. Choose the amount of  
detergent depending on the fabric type and  
water level.  
mounting section,  
and push the leg in  
2
1
the arrow direction  
as shown in the  
Leg  
Bottom face of  
main body  
Hose holder  
figure until it clicks.  
 
5
AFTER OPERATION  
MAINTENANCE  
TROUBLE SHOOTING  
1. Remove the power cord from the outlet.  
2. Take out the laundry.  
3. Close the water tap and disconnect the water  
supply hose.  
4. Clean the washing machine.  
- Periodical cleaning will extend the life of your  
washing machine.  
TO LOAD THE LAUNDRY INTO  
THE SPIN BASKET.  
Press the laundry evenly and put the safety  
cover into the spin basket as shown in the  
figure.  
TROUBLE  
CHECK POINT  
The washing  
machine does properly connected to a power  
not work.  
Check that the power cord is  
outlet. Isthere a power failure?  
Clothes do  
not move freely.  
Is the machine overloaded?  
- Do not spray the unit water or use tinner, benzene,  
alcohol etc, for cleaning it.  
Is the laundry arranged  
evenly?  
Incomplete  
spinning  
Incomplete  
draining  
Is the filter clogged with lint?  
TO RETRIEVE THE CLOTHING THAT HAS  
FALLEN BETWEEN THE BASKET AND TUB.  
For safety reason, pull the power supply plug out  
of the socket.  
1. Unscrew the spin dryer hatch.  
2. The spin dryer hatch is  
Is the spin dryer lid closed  
completely?  
Are laundry items (socks, etc.) falling  
out of the spin dryer basket and  
clinging to the axle?  
The spin dryer  
basket will not  
run.  
See To retrieve...on page 6.  
fixed to the brim by the  
concave and convex  
parts at two places.  
Expand the concave and  
convex parts,and pull up  
CLEANING THE WASHING MACHINE  
Wipe off stains on the cabinet and operation pane  
with a soft cloth. Neither use benzene, thinner,  
cleanser, or wax, nor scrub the washing machine  
with a brush. Painted surfaces or plastic parts will  
be damaged.  
the spin dryer hatch to  
remove it.  
3. Retrieve the clothing.  
4. Close the spin dryer hatch. Push the hatch  
firmly until the catch at the front is securely  
attached.  
 
6

Q See Car Video System QR40198 403 User Guide
Quasar MP3 Player PPX2000 User Guide
Radio Shack Car Speaker PRO CSW1200 User Guide
RCA Clock RCD10 User Guide
Ryobi Trimmer RY24600 User Guide
Samsung Home Theater System HT C6900W User Guide
Samsung Laptop A3LSGHI987 User Guide
Sanyo Flat Panel Television CE52FD86N B User Guide
Sanyo Projector PLC XW50 User Guide
Sanyo Projector PLV HD10 User Guide